Suitable for fixing fast hydraulic lines and electrical conduit to concrete, concrete block and hard wood with tempered steel nails with washer TR85.

These hardened steel nails for nailer are supplied for all concrete surfaces and concrete blocks. This nail typology assembles a Ø20 mm washer.

These hardened steel nails for gas nailers are power supplies for applications on all concrete surfaces and concrete blocks.They can come with three different forms of packaging.

The Tie-rod’s continuous thread is cold-rolled onto the steel. Size Ø15/17mm, Length is available 6mtr. Working load is 90KN and breaking load 190KN. For all types of concrete structures.

Malleable Casting as per BS32-12 Standard, Inner dia.15 mm. Outer dia.27 mm. Wing width: 95 mm. Base dia.35 mm. Cast Iron FCD 45 Galvanized. Working Load: 100 KN Ultimate Load: 190 KN. (For Tie rod 15/17mm Día).

Material mild steel, Finish Zinc plated, Yellow Zinc plated, Corrosion resistance Size 120x120x4,5,6,8mm, Application on the tie rod.

water barrier flange type. Malleable iron, for spacer tube with internal diameter of 26mm, loading capacity 90KN, malleable casting Galvanized. Threading is suitable for 15/17mm tie rod. Available with 2 pcs. of plastic adaptors.

Body is made of Malleable Casting and the Pin is made from Forged Steel. The Teethes on the Wedge is Heat Treated for Maximum Life. The simplest way of locking the form Tie-rebar just by a hammer. Repetitive use with rebar dia. 6 mm., 9 mm. and 12 mm.

Shuttering clamps is used to support scaffolding at construction sites. Clamps are hot-forged to ensure zero breakage & loss during application. With these shuttering clamps, there is no need of screwing, nailing, bolting, or drilling to construct Scaffolding at construction site. Corrosion resistant surface, can withstand high load Robust in construction.

The Plastic Wheel Spacer is the most extensively used circular spacer for precast and on site concrete applications. The Clip spacer has proved to be the most popular of our range of plastic clip on spacers. Designed for heavy-duty applications it is a robust spacer that accommodates bars. All Standard range are available.

Used as a distance spacer between formwork faces, they allow tie rods to be withdrawn for re-use. PVC CONE and PLUGE are manufactured from rigid PVC, a wide range of single use plastic cones, for use with PVC tube 22mm to 32mm diameter.

PVC chamfer triangle ton types, were products used in construction. By using a wooden cornice triangle. The negative corner is that when it comes out as a negative pole at the corner of the rail bridge footpath along the edge of the road embankment.

Water stops are high quality pvc joints whose mechanical and elastic properties Guarantee excellent performances. Their specifications are maintained in the long-term even at low temperatures (from -30°C up to +60°C). They do not require special warehousing or conditions. They resist to ageing and to chemical attack in alkaline environments but also to brackish water or acid solutions. They are designed to resist to the high stresses the building is subjected to during settlement. The welding either with hot air or heated blades can be carried out on site.

Construction Poly Sheets are mainly used for the construction sector. It helps in separating the dry ground and the wet concrete. So, that concrete can take its own time for dry and avoids the possibilities of cracks and other damages.

Jolly Board Expansion Joint Filler is manufactured from water resistant, bitumen impregnated, cane fiber. It is available in a wide range of sizes, both as boards & strips in thicknesses of 10 MM, 12 MM, 18 MM, 19 MM, 25 MM. Jolly Expansion Joint Filler displays excellent resistance to compression, with outstanding recovery characteristics. The fillers are environment friendly as opposed to the environment destroying thermocole/plastic expansion joint filler.

Designed for creating a wider shadow gap during construction, Architrave Beads creates clean plaster edges that about with the concrete frame in such a way that the edges of the construction does not damage at all. In addition to this, Architrave Beads that is extensively used as plaster stop profile, while creating a shadow like decoration around door and window frames. Moreover, Architrave Beads when used in construction, increase the speed of installation and finishing process dramatically.

Rib Lath is extensively used for plastering background for suspended ceiling, partitions and walls.

Galvanized steel and stainless steel, Coir Lath is widely used as a plastering base in order to reinforce the concrete against cracks between joints. Coil Lath is extensively used in crack prone areas. Moreover, Coil Lath is used for external wall to offer sturdiness to the structure.

Couplers are the fittings which hold the tubes together. The most common are called scaffold couplers, and there are three basic types: right-angle couplers, putlog couplers, and swivel couplers. To join tubes end-to-end joint pins or sleeve couplers are used. Only right angle couplers and swivel couplers can be used to fix tube in a ‘load-bearing connection.

All W&D standards incorporate lower fixed cups at 0.5m intervals with captive rotating topcups which secure up to four components. Access standards incorporate a 150mm spigot at the top to allow the vertical connection of further standards. Provision for a locking pin or bolt is also provided.

All ledgers incorporate symmetrical forged blade ends making assembly quick and simple, and allows components to be completely interchangeable. Horizontals locate in the bottom cups of the standards and are secured by locking the top cup.

These units are designed to provide intermediate support for standard scaffold boards by spanning between the inner and outer ledgers. The jaw section at each end is turned downwards to prevent dislocation. One end is provided with an integral locking device to prevent movement along the ledgers during use.

Combined jack and base plate.

Universal jacks have an adjustment of up to 0.5m and are used to accommodate variations in ground levels and to level the structure. They are used in conjunction with base/head plates and fork heads. U-Heads are designed to be used in conjunction with Adjustable System Scaffolding. The main function of a U-Head is to hold timber beams securely in place.

300mm Spigot pins are incorporated at the top of the standards/ verticals to allow the vertical connection of further standards/ verticals. Provision for a locking pin or bolt is also provided. The Spigots are also available with washers to further secure the connection.

Used in conjunction with the universal jack. The spigot is drilled to allow for the insertion of a securing bolt if required.

All ledgers incorporate symmetrical forged blade ends making assembly quick and simple, and allows components to be completely interchangeable. Horizontals locate in the bottom cups of the standards and are secured by locking the top cup.